- How do you install Man wires?
- Are cable wires dangerous?
- How do you tighten a wire?
- What is a head guy?
- What does guy wire mean?
- Are guy wires dangerous?
- What is meant by Guy?
- How tight should guy wires be?
- What is EHS guy wire?
- Is it a guy wire or a guide wire?
- What is a down guy?
- How do you tighten cable wires?
- What is a wire stay?
How do you install Man wires?
Ideally, the guy wires should extend out from the mast at a 45° angle, and should be anchored in screw eyes placed 120° apart (Figure 2).
(If four guy wires are used, they should be anchored in screw eyes 90° apart.) Be sure each screw eye is firmly anchored in solid wood at least five feet from the base of the mast..
Are cable wires dangerous?
Hazardous Electrical Charge The most obvious reason why wires are so dangerous is because they carry electrical currents. If that electricity is kept contained within the wires at all times, there is very little risk.
How do you tighten a wire?
Pull the loop around the post and fold it over the strand of wire. Push your bolt through the loop. Use the lever to twist the loop around the strand of wire and continue twisting until the fence is tight. Pull the bolt out of the loop and cut off the ends of the wire.
What is a head guy?
HEAD GUY. A head guy runs from one pole to the next pole down the line. It is used to transfer the load supported by one line pole to another, as shown in figure 2-12.
What does guy wire mean?
A guy-wire, guy-line, or guy-rope, also known as simply a guy, is a tensioned cable designed to add stability to a free-standing structure. They are used commonly in ship masts, radio masts, wind turbines, utility poles, fire service extension ladders used in church raises and tents.
Are guy wires dangerous?
Guy wires are support structures that are anchored into the ground, to keep poles and energized conductors from falling, or sagging too much. They do not carry power, and, therefore, do not create an electrical hazard, unless poorly maintained. … Still, it’s never safe to touch a guy wire.”
What is meant by Guy?
(Entry 1 of 4) 1a : man, fellow. b : person —used in plural to refer to the members of a group regardless of sexsaw her and the rest of the guys.
How tight should guy wires be?
Rohn specifies that guys should be tensioned to 10% of the breaking strength of the guy size that is recommended for a particular tower. One rule of thumb is 8% if the guy is out at 100% of tower height, 10% ifat 80% of tower height (standard Rohn drawings) and up to 15% if the anchor point is at 65% of tower height.
What is EHS guy wire?
Guy wires. Also known as guyed wire, guy cable, guy strand, guy anchors, or even mistakenly called ”guide wire,” this Extra High Strength (EHS) cable is available in two configurations: 1×7 (sizes range from 1/4” up to 5/8” in diameter), and 1×19 (sizes ranging from 11/16” to 7/8”).
Is it a guy wire or a guide wire?
The Guy Wire Name Some refer to it as guyed wire, others guy cable, and still others guy strand or guy anchors. People will also mistakenly refer to it as guide wire, when in fact the term is derived from the term guy, which is a rope, cable or cord used to steady, guide or secure.
What is a down guy?
TERMINAL DOWN GUY. As shown in figure 2-9, this type of guy is usually placed at the end of a pole line to counterbalance the pull of the line conductors. The terminal down guy can, at times, be called a corner guy.
How do you tighten cable wires?
How to Tighten a Steel CableUnscrew the eyes on both end of the turnbuckle until they are as far apart as possible without falling out of the buckle. … Slide two cable clips onto one end of the steel cable. … Insert the cable through one eye of the turnbuckle.Fold the cable back on itself and slide the cable clips over the tail.More items…
What is a wire stay?
Stay Wires are galvanized steel wire strands that are used for sustaining mechanical load. Generally they are made up of 6 wires stranded around 1 wire, twisting 7 wires together. A common use for stay wires is in the electricity industry, using the wire to stay power poles and tower structures.